A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
On this page below you'll find more awesome points regarding Tools You Need to Install a New Bathtub .
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is easily obtainable, the job can move easily; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly require an assistant to move out the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the task and fit attempting it. Instead of employing a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might require a specialist plumber to make tube links.
This write-up will help you install a brand-new bath tub in your shower room if you have already bought a brand-new tub and also don't need to change the plan of your previous water pipes.
Your tools as well as material checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipes have been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Protect the tap in position with the supplier offered backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bathtub
Using both wooden boards under its feet, place the bath tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the tub up until the spirit level reads level.
To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system and check all joints as well as new pipework for leaks and also tighten them if essential. Fill the bath tub as well as additionally check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and also securing around the bathtub should wait till the bath tub has been used a minimum of when as this will resolve it into its final position.
Getting ready for the Installation
First of all, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall surface in between the bathroom and the tiling, leading to complications with moisture and possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your components and also installations. They are sold in tubes as well as cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can crack rather very early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very involved in A Step-by-Step Guide to Installing a Bathtub and I really hope you liked the entire blog entry. Those who enjoyed our article plz don't forget to pass it around. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Plumbing SOS? Dial! Report this page